The SD Pro is our first .300 Blackout upper and is intended for use with a suppressor that fits under the handguard. The Aero Enhanced handguard has an ID of 1.72" and should fit all 1.5"-1.6" OD cans. These have a 8.3" BA Hanson barrel under the 10.7" Aero handguard and come with a KAK flash can to extend beyond the front of the handguard.
These are setup for mixed ammo and should run everything right out of the box. However some subsonic ammo may require lighter springs or buffers when unsuppressed.
The Basics
8.3" BA Hanson barrel, Aero Precision 10.7" Enhanced Mlock Handguard, Chrome/Nitride BCG, Aero M4E1 Upper, and Aero Breach Charging Handle
The Specifics
Barrel:
Manufacturer - Ballistic Advantage
Length/Chamber - 10.7" / .300BO
Twist - 1:7 Twist
Material - 4150
Profile - Hanson
Gas System - Pistol
Finish - Nitride/NIB
Thread Pitch - 1/2x28
Weight - 19oz
Factory Pinned
1st Rebarrel - FREE
Barrel nut is sequentially torqued down to 50 FT-lbs. Starting at 25, then 35, and then finally 50 FT-lbs to ensure proper mating of the threads.
Barrel is also bedded to the upper receiver with an expanding/hardening compound to ensure perfect fit and reliable accuracy.
If you legit burn out a barrel, like 10,000 -25,000 rounds, and the barrel becomes inaccurate I will rebarrel it for you for free. Good luck.
Bolt Carrier Group:
Bolt Material - 9310 MPI
Carrier Material - 8620 Alloy
Gas Key Material - 4130 Alloy
Profile - Full Auto
Finish - Chrome/ H&M Nitride
Gas Key Screws - Grade 8 (torqued and staked to Mil-Spec)
Forward Assist Cuts
Mil-Spec Firing Pin (Hard Chrome Coated)
Handguard:
Manufacturer - Aero Precision
Length - 10.7"
Material - 6061 T6 Aluminum
Finish - Hard Coat Black Anodization
Mounting Platform - Mlock
Barrel Nut - 7075
Barrel nut torqued to 50 FT-lbs
8 handguard set screws are torqued to 10-inch pounds for easy removal and installation of your suppressor. Re-instal to 25 in-lbs with blue loctite. I can also do that here if you plan on using the flash can for a while.
We apply a Permatex Anti-Seize solution to the receiver extension before installing the barrel nut to ensure they do not lock up over many years of hard use.
Upper Receiver:
Manufacturer - Aero M4E1
Material - 7075 T6 Forged Aluminum
Finish - Type 3 Hardcoat Anodized Black
Standard Forward Assist
Standard Dust Cover
M4 Feed Ramps
T-Marked
Charging Handle:
Manufacturer: Aero Precision Breach
Material: 7075 T6 Aluminum
Finish - Type 3 Hardcoat Anodized
Extras - Machined in cuts to deflect gas when shooting suppressed.
Gas Block:
Material - 4140 HT Steel
Style - Low Profile
Size - .750"
Attachment Method - 2x Set Screws
Factory Pinned
Not Adjustable
Set screws are torqued to 30 IN-lbs and have a high temp threadlocker applied for ultimate security.
Gas Tube:
Length - pistol
Material - Stainless Steel
Finish - Black Nitride
Flash Hider:
Kak extended flash can
Thread Pitch - 5/8x24
Caliber - .300
SD Pro - 8.3" .300 Blackout
Our stated policy is to not accept returns, but if you accidently ordered the wrong item or there was a mistake or if you have any issue at all send us an email (listed in the "contact us" section) and we will work it out.